vShare 2.7, New Account user Can Not Upload Video???

**Hollywoodstarrs** · 03-22-2011, 12:36 AM

Ok, I have done almost everything to get this software operational. I admit alot was a learning curve on my part, as my linux server needed some adjusting. Apparently Godaddy.com does not provide FFMPEG, MPLAYER, FFMPEG-php, FLVtool2, and MENCODER as part of their virtual dedicated server performance. I had to also enable the GD Library as well. Once i have all of that uploaded and ready I tried to upload a video with no success. I also have access to the server root.

The problem is that when I go to my user account and try to upload a video (55mb on my computer) I end up waiting for like 10min and there is no confirmation page. When it stops uploading with the upload_file.php the page goes back to the original setup as if I never tried to upload a video. Suggestions please!!!!
I followed the thread post at this url: http://forums.buyscripts.in/frequent...p-problem.html No luck after that.---Allen

**Hollywoodstarrs** · 03-22-2011, 01:14 AM

So I was able to upload a remote server video (Youtube.com) with no problem. I was also able to email "view" messages to anyone as well. Alright...I am almost there. I just need it to upload from my PC.----Allen

**buyscripts** · 03-22-2011, 03:51 AM

Login to admin area and check the status of video at

admin area = > Video Processing = > Process Queue

Also post your URL here

**Hollywoodstarrs** · 03-22-2011, 04:54 AM

Originally Posted by buyscripts

Login to admin area and check the status of video at

admin area = > Video Processing = > Process Queue

Also post your URL here

My URL is www.ettv.com and there are no videos in the process queue. ---Allen

**Hollywoodstarrs** · 03-22-2011, 04:56 AM

This is just a guess, but maybe the upload_file.php or .tpl are corrupted?---Allen

**buyscripts** · 03-22-2011, 05:03 AM

Open a support ticket at

BuyScripts Helpdesk

with your vshare admin and FTP login details.

**Hollywoodstarrs** · 03-22-2011, 05:23 AM

Originally Posted by buyscripts

Open a support ticket at

BuyScripts Helpdesk

with your vshare admin and FTP login details.

I went and created my support ticket ---with my FTP and vShare Admin panel access.
Support ticket #247129

---Allen

**Hollywoodstarrs** · 03-22-2011, 06:56 AM

I wanted to complete this forum discussion with the solution that my support ticket provided to me. I will give their solution a try and post the results.---Allen

HERE IT IS:
MPlayer was compiled without libmp3lame support.

Contact your webhost to recompile mplayer with libmp3lame support.

Your Friendly,
Buyscripts

**bplex** · 03-22-2011, 03:22 PM

Based on that response, it appears as though your ffmpeg and mplayer installation was installed by themselves without their prerequisites. Who did your installation?

**Hollywoodstarrs** · 03-22-2011, 07:17 PM

Originally Posted by bplex

Based on that response, it appears as though your ffmpeg and mplayer installation was installed by themselves without their prerequisites. Who did your installation?

I did the initial install of FFMPEG and MPlayer. I then turned the install of FLVtool2, MENCODER and FFMPEG-php over to a software engineer. I used directions found at this blog--

· FFmpeg: svn checkout svn://svn.mplayerhq.hu/ffmpeg/trunk ffmpeg (http://www.babapandey.com/installing-ffmpeg-on-vps/ )
· Mplayer: svn checkout svn://svn.mplayerhq.hu/mplayer/trunk mplayer (http://forums.site5.com/showthread.php?t=27310 ) bottom of page

My friends response to this was as follows: You didn't have the binaries for ffmpeg nor mplayer. All you had on the server was the source code for these packages. Now I have to create a build from source code and maybe install extra dependencies.

Any suggestions available to complete the installation of FFMPEG or Mplayer for forum discussion visitors?----Allen